Views: 0 Author: Site Editor Publish Time: 2026-11-19 Origin: Site
A hydraulic wheel drive uses pressurized oil to turn the wheels of a machine such as a compact loader or a self-propelled sweeper. In a direct drive, the wheel turns at the motor’s output speed. In a geared drive, a reduction gearbox lets a faster-turning motor deliver more torque at the wheel. Start with three questions when comparing the options. How fast must the machine travel? What does it take to start under load? Which bearings carry the wheel? The answers tell you what performance figures and drawings to request before ordering.
A wheel drive can move a self-propelled boom lift around a jobsite, take a compact loader across a yard or move an agricultural machine along rows. The same label covers equipment that spends most of the day creeping and equipment that must travel between work areas. On a machine with separate hydraulic drives for its work and travel functions, the drive that moves the wheels has a different job from the motor that turns a brush, an auger or a conveyor.
Take a sweeper as an example. The buyer may need a drive that turns the wheels gently while the operator works along a curb, then moves the machine at a higher travel speed between jobs. The two speeds come with different requirements for torque and control. The brush may also turn while the machine advances. When this happens, find out whether the work and travel functions share their hydraulic supply. That affects what power is available for either task at a particular moment.
For a compact loader, the demanding part may be starting with a full bucket on an incline. A quote with a satisfactory running speed still needs evidence for the start. Add the surfaces the machine uses, whether it works on slopes and how it turns. Some machines steer the wheels through joints. Others turn by driving wheels on opposite sides differently. The wheel, mounting and drive design need to suit that particular arrangement.
Machine or duty | What the buyer should identify early | What you can do with the answer |
|---|---|---|
Slow work in rows or near a curb | Lowest controllable speed with the real load | Ask for smooth operation in that part of the range |
Frequent transfers between worksites | Maximum travel speed and how long it is sustained | Check whether the drive can stay there without exceeding its duty limits |
A machine that starts loaded | Normal load, typical slope and start frequency | Ask for available start torque and review the holding and braking system |
A machine with an existing wheel-drive failure | Assembly code, old drawings and the condition that preceded the failure | Identify the part and whether a replacement faces the same conditions |
A tractor or machine may also send power through one hydraulic motor to a mechanical axle. Another design may put a motor or motor-and-gearbox assembly at each wheel. Ask for the drawing at the level at which the force is transferred. Hoses next to a wheel identify part of the drive. The hub, axle, differential or gearbox determines how the motion reaches the tires.
An engine or electric motor turns a hydraulic pump. The pump supplies oil flow to the drive circuit. The pressure difference across the wheel motor makes it develop turning effort, called torque. Oil flow through it influences how fast it can run. An oil passage back out of the motor is part of the circuit, and the pressure in this passage affects the pressure difference available to turn the motor.
The control arrangement depends on the machine. In one open-circuit design, oil travels from the reservoir through the pump and control valve to the motor, then returns toward the reservoir. A hydrostatic transmission often has a closed main loop. In that arrangement, the working flow from the motor returns to the pump, and a charge circuit replenishes losses and supports the loop. A machine with a closed-loop travel drive may still have a separate open circuit for its attachment.
A vehicle goes into reverse when the drive circuit and mechanical arrangement deliver torque in the other direction. In a reversible circuit the working lines can change roles. A motor's cast-in port letters stay the same. It takes the machine schematic and the manufacturer's shaft-view convention to tell which supply path produces the desired wheel rotation. Ask for that convention when an old drive must be matched on both sides of a machine. Danfoss Series 90 motor technical information, system design
A brake may be built into a drive assembly or installed separately. Some configurations support a parking function through a spring-applied, hydraulically released brake. The catalogue and the machine instructions establish whether that brake is intended only for holding, and whether a separate service or emergency braking arrangement is needed. On a slope the wheel load can drive the motor, changing the energy path. The vehicle maker's braking and control design governs that condition. Poclain hydraulic motor selection guide, braking options
A drive also needs a way to coexist with the rest of the equipment. If a travel function receives most of the available flow on its own, it may respond differently when a steering or work circuit makes a demand. Check what the machine is intended to do simultaneously. On machines with independent wheel motors, the circuit design determines how flow and torque are distributed during a turn or when traction differs between wheels.
The term direct drive describes the speed relationship. The output of the motor turns the wheel without a speed reduction between them. The wheel may attach to a motor flange designed to carry its loads, or a separately supported wheel hub may receive torque through a coupling. Two layouts can therefore have the same speed ratio and different load paths through the bearings.
A compact wheel-mount motor can put its flange partly inside the wheel, depending on design. Bringing the wheel load closer to the intended bearing position helps the motor use its published load capacity. Danfoss describes this geometry on certain OMTW and OMVW orbital wheel versions. That manufacturer example shows why the installation drawing matters. A standard motor from the same broad family can have a different support arrangement. If you are comparing hydraulic motor mounting styles, use the mounting guide to identify the physical form, then go back to the exact drawing for the permissible loads. Danfoss orbital motor technical information, motor variants
In a geared wheel drive, a motor turns a reduction gearbox. A planetary reduction is one common package. A ratio of 4:1 means roughly four motor turns per wheel turn. Ignoring losses for a moment, the wheel would receive four times the torque at one-quarter the speed. An actual gearbox loses some power, so the resulting wheel torque is lower than that ideal. The gearbox maker defines the permitted torque, speed, wheel loading and duty for its design.
The gearbox also changes the dimensions and service questions. Some assemblies bolt the wheel to the rotating gearbox flange, with the gearbox bearings carrying the load. Others send torque to a separately supported axle. If a replacement has the same output ratio but shifts the wheel outward, the altered offset can change the load on the bearings and chassis. Use the assembled drawing rather than judging fit from the motor flange.
Question | Direct drive | Motor and reduction gearbox |
|---|---|---|
How fast does the motor turn? | At wheel output speed | Faster than the wheel by the gear ratio |
Where is wheel torque established? | At the motor output, subject to the coupling if fitted | At the reduction output, after allowing for losses |
Where does the side load go? | Into a rated motor bearing arrangement or a separate hub support | Into the gearbox or axle support specified by the assembly drawing |
What tends to change the shortlist? | Stable low-speed output, start torque, packaging and bearing limits | Ratio, geared shaft torque, fit, lubrication and combined limits |
A geared option can make sense if the motor has a useful working band at a higher speed. A direct motor can suit a machine that needs slow wheel rotation and has room for the required displacement and bearing arrangement. Both need a compatible control range. If a supplier suggests the layout based on a photograph, ask for the drawing and performance evidence that relate it to the machine.
An orbital motor is a common family to consider for low-speed work. You may see it listed as a gerotor or roller-stator design, depending on how the rotating group is made. In simple terms, fluid acts on the internal gear set to turn the output. Orbital motors come with different displacements and mounting options. If an axle has its own wheel bearings, a shaft-type orbital motor may serve as the rotating power source. If the wheel itself will sit on the motor, check the exact wheel-supported version and load chart.
A radial piston motor has pistons arranged around the axis of rotation. Radial piston families include configurations for high torque at relatively low speed, and some manufacturers offer versions that carry the wheel on a rotating flange. A wheel version and a shaft version can appear in the same technical catalogue. They must be identified by model options and drawings. Within one family there may also be several brake and displacement arrangements. Poclain hydraulic motors, wheel and shaft design examples
An axial piston motor has a different internal layout. It can appear in a hydrostatic transmission with a gearbox or axle. Some models have variable displacement, which means the amount of oil corresponding to one revolution can change with the control setting. That changes the relation among flow, speed and torque. The motor and the transmission have to be checked as a set, including how a change of mode is managed in the machine.
Size, motor name and port size are useful identification details. A catalogue family also gives a first idea of the sort of operation a design can cover. Start the decision from speed, loaded start and wheel support. If the earlier machine already has a bearing-supported axle, the shortlist can include configurations quite different from the shortlist for a wheel bolted straight to a motor flange.
Think of torque as the effort on a wrench. The farther you pull from the center and the harder you pull, the more turning effort you apply. At the wheel, the same relationship connects the pulling force at the tire with its loaded rolling radius. A bigger tire covers more ground in one turn. It also takes more wheel torque to produce the same pulling force at a larger radius.
For a preliminary estimate, obtain the wheel's loaded rolling radius from the tire or vehicle data. Use a common unit for speed and circumference. The following assumes steady travel with negligible slip and a steady load. Use the pulling force assigned to the wheel you are evaluating. A total vehicle pulling force requires a drive-load distribution from the machine design before you can calculate a per-wheel requirement.
Wheel speed is travel speed divided by the distance traveled in one wheel turn. Use metres per minute and metres per turn to obtain rpm.
Wheel torque is the effective pulling force at that wheel multiplied by its loaded rolling radius. Newtons times metres gives newton-metres.
Wheel power is torque in N·m times rpm divided by approximately 9,550 to obtain kilowatts. Multiply kilowatts by about 1.341 for mechanical horsepower.
Suppose a buyer's engineering team specifies 6 km/h for steady travel on a particular surface in the work cycle. The tire has a 0.32 m loaded rolling radius. The team estimates that one drive wheel must deliver 2,400 N of tractive force at that steady running point. These are illustrative inputs. They are not ratings for any machine or BLINCE product.
Step | Arithmetic | Approximate requirement |
|---|---|---|
Distance per wheel revolution | 2 × π × 0.32 m | 2.01 m |
Wheel speed | 100 m/min ÷ 2.01 m | 50 rpm |
Wheel torque | 2,400 N × 0.32 m | 768 N·m |
Wheel power | 768 N·m × 49.7 rpm ÷ 9,550 | 4.0 kW, about 5.4 hp |
Motor speed with a 4:1 reduction | 49.7 rpm × 4 | 199 rpm |
Motor torque at an assumed 90% gearbox efficiency | 768 N·m ÷ (4 × 0.90) | 213 N·m |
Motor shaft power with that gearbox | 4.0 kW ÷ 0.90 | 4.44 kW, about 6.0 hp |
A direct candidate would have to supply approximately 768 N·m at 50 rpm at its output for the same running point, assuming the torque reaches the wheel without a material additional loss. The geared candidate needs closer to 213 N·m at 199 rpm at the motor shaft. Each candidate must operate at the stated pair under load. The gearbox alone accounts for the difference between the 4.0 kW at the wheel and the 4.44 kW the motor must supply at its shaft in this example. Use the paired torque and speed when comparing the candidate with its published limits.
Now compare the required motor output with the power the branch supplies. If the geared motor must deliver about 4.44 kW and its compatible overall efficiency is assumed to be 80%, the working ports need about 5.55 kW of hydraulic input. At an assumed 120 bar pressure drop across the working ports, the simplified flow estimate is about 27.8 L/min (5.55 × 600 ÷ 120). That figure demonstrates how to relate shaft horsepower to hydraulic supply. You still need the exact motor curve, supply data, return pressure and the expected operating range. Separate case or charge flows may need their own accounting. Danfoss Series 90 system design formulas
The calculation is useful in a sourcing conversation because it identifies two different places to quote power. Knowing how to read a hydraulic motor performance curve at the intended duty helps you ask for evidence at the same torque and speed. If the supplier quotes 6 hp, ask which shaft it describes and whether the accompanying speed belongs to the same test point.
Tire size can change after a machine leaves the factory. A buyer may also want a different wheel for soft ground. Imagine increasing the loaded radius in the example from 0.32 m to 0.384 m. At the same 6 km/h, wheel speed falls by about one-sixth, from 49.7 to 41.4 rpm. To keep delivering the same 2,400 N at the tire, wheel torque rises by 20%, from 768 to about 922 N·m. The ideal mechanical power at the wheel stays about 4 kW because the same force acts at the same ground speed.
That example explains why horsepower alone can miss the problem. The drive must handle a heavier torque requirement, and the tire and rim may move the load away from the original mounting position. Getting the original wheel number and the proposed drawing helps a supplier check both the speed and the load before giving an answer. Actual ground grip, pressure distribution and tire behavior can also change.
A machine parked on a slope can require substantial torque to start even though the wheels are standing still. Shaft power is zero at zero speed. As the wheels begin moving, torque and speed together determine mechanical power. A product's running horsepower figure therefore does not establish reliable starting under load. Ask which manufacturer data apply at start, and whether the drive's control and oil supply can deliver the required condition.
For a working machine, write out its day in simple steps. One step might be starting fresh each time an operator picks up a load. Another might be crawling for a minute while an attachment works. A third might be five minutes of transfer at higher speed. A turning maneuver can add a load that isn't clear from a straight-line travel speed. Add how often each operation repeats so suppliers can show which points fall within the motor's continuous, intermittent and peak duty.
Traction matters too. A bigger motor can turn the hub with more torque when enough pressure is available. The tire and ground set how much of that effort becomes useful pulling force. If the current wheels spin on wet ground, a quote based solely on motor torque misses information about weight at the wheels, surface, tires and how the machine distributes drive. A useful decision record says what the operator observed before assuming which part should change.
For a replacement, record the brake and control connections shown on the machine schematic. Ask the supplier to identify the equivalent functions on the candidate drawing. A separate parking-brake connection and a two-speed shift connection can both appear near smaller ports, so use the full assembly code to identify each one.
Start with the existing machine and the complete identification of the drive. A serial number or a piece of a model code can be helpful. Outwardly similar models can have different torque characteristics, brake connections, rotation arrangements or mount details. A clean image of the whole drive and a legible nameplate give the supplier a starting point. Add the old drawings or machine parts listing when available.
Next, identify which part you are buying. Replacing the motor alone generally leaves a gearbox, wheel and bearings in place. Buying a complete assembled drive brings more interfaces into the order. Write down whether the wheel fastens to a hub, output flange or an axle somewhere downstream. Then record what fixes that assembly to the chassis. The bolt and pilot dimensions need their proper reference faces so the supplier is comparing the right drawing features.
Small dimensional changes can matter. A pilot diameter is the locating fit between the parts. The bolt circle sets where the fasteners go. Offset locates the wheel centerline relative to a mounting face. If two drawings use different faces as their starting point, mark each with the relevant dimension before comparing. Ask for a verified permissible wheel load at that offset. There is no universal rating for adding a wheel to a motor output.
Follow the existing hydraulic connections on the drawing and record working ports, case drain, and brake release or shift connections where supplied. Identify the hose or tube ends and how much access remains after the wheel is mounted. A buyer could match the port thread yet find that the fitting cannot turn into position because the new housing is shaped differently. Use an assembly view when clearance is tight.
Item | What to record before comparing offers |
|---|---|
Machine and duty | Equipment make, function, load, surface, travel speeds and starts under load |
Existing drive | Complete model code, machine part number, photos and brake or shift options |
Wheel and support | Loaded rolling radius, tire/rim drawing, hub drawing, offset and which bearings carry the wheel |
Frame and connections | Mounting pilot, fasteners, shaft or output flange, and working, drain and brake ports |
Performance | Motor branch flow, working-port pressure drop if available, and required wheel torque and speed at the same point |
If the drive came off a machine with unusual noise, slow travel or oil at the hub, add the operating conditions and the location observed. A photograph of fluid on the wheel does not establish where the leak began. The record helps determine which drawings or service checks should precede a purchase. A repeated failure should prompt a review of the original conditions and installation, even when the old assembly is easy to identify.
BLINCE's hydraulic motor range is a starting point when a new machine could use more than one motor architecture. Record the drive layout first. If the application uses a separately supported hub and you are reviewing orbital motors, the BMK2 orbital motor page lets you identify the family and request the documentation for a candidate build. Final suitability depends on the required speed, torque and duty and on how the wheel is supported.
If your machine paperwork identifies an HMS02/HMSE02 radial piston travel motor, use the full variant, mounting interface and any brake configuration to identify the correct drawing. The product page covers a family with multiple decisions still to make. Its presence in a catalogue establishes neither interchangeability with a different manufacturer nor a rating for the example above.
A bid is easier to compare when every vendor uses the same wheel requirement, refers to the same assembly boundary, and lists any assumptions. Request one normal operating point and one loaded start condition. For a geared assembly, request the motor and gearbox ratings together, including which assembly carries the side load. Those details can also help a distributor decide what they can quote confidently and what needs a manufacturer check.
Send BLINCE your machine type, wheel size, typical ground and load, desired travel speeds, and the existing drive code if you're replacing one. Include drawings for the wheel and drive mount where available. A useful initial reply would identify a candidate family and confirm which fit or duty checks are still open. For a vehicle using a separate brake or two-speed control, include that information with the drawing.
Wheel motor usually describes a motor intended to drive a wheel, sometimes as a purpose-built wheel-mount configuration. Travel motor is a broader equipment term for a drive that moves the machine. It may refer to motor-only or geared assemblies and wheeled or tracked equipment. Use the machine drawing and model code to establish what is included in a quotation.
Yes. Displacement is the amount of oil a motor theoretically uses per revolution. Actual operating speed also depends on incoming flow, internal leakage, gearing and wheel radius. If the machine uses multiple motors, the circuit determines what flow each receives. Compare the measured travel condition with the appropriate flow and hydraulic motor speed calculation before interpreting a model label as a speed figure.
A higher pressure difference can give the motor more torque, and available flow affects speed. The motor, pumps, wheel assembly, hoses and controls have design limits. A machine with poor traction, an incorrectly matched gearbox or a brake that fails to release fully needs a different diagnosis. Compare the output requirement with the machine's approved operating envelope before considering changes to supply.
Ask which original parts drawing or complete drive code is needed. Share the make, model and serial number, photos of the label and mounting, and the job the machine must perform. If a tire, hub or brake has been changed, include that detail. A supplier may be able to narrow the family first and request the dimensions necessary to identify the exact assembly.
Tel: +86 132 4232 1601
✉️ Email: info@blince.com
Website: https://blince.com/
This article is a general engineering guide. Final component selection should be based on machine drawings, measured hydraulic data, working conditions, safety requirements, and confirmation from a qualified hydraulic engineer or supplier.
Blince Hydraulic is an industry-leading company dedicated to precision-engineered fluid power manufacturing and custom hydraulic solutions. Backed by decades of deep field expertise in industrial machinery and thousands of successful global deployments, our engineering team focuses entirely on high-performance hydraulic component manufacturing, including specialized orbital motors, high-pressure travel drives motor, and robust directional control valves. Our production infrastructure utilizes state-of-the-art multi-axis CNC machining systems and is fully ISO 9001 certified to guarantee repeatable volumetric accuracy across every single manufacturing run.
We deliver fast, highly dependable, and cost-efficient hydraulic solutions to heavy industry distributors, machinery OEMs, and maintenance crews across more than 150 countries. Whether your active project calls for a small-volume batch of customized shaft profiles or a large-scale production run of severe-duty cast iron gear pump, we configure our flexible production schedules to meet your target lead times with total pricing predictability. Partnering with Blince means securing maximum system efficiency, elite material quality, and uncompromised fluid power professionalism.
To learn more about our complete product lineup, visit our official website: www.blince.com.